[C.CC USERS] Neither blink() nor heartbeat() run on arduino tvm on seeeduino mega V1.23 ?

[Matt Jadud]

Hi Vjeko,

I used to own a Seed 1280 board, and it worked. We support the 1280,
and have pin mappings for it. I have been meaning to buy a replacement
for some time, though, as I no longer own one.

I will be travelling tomorrow AM through Sunday. If anyone is able to
provide some pointers/ideas for Vjeko, that would be marvelous.

We'll get you running; I'm sorry that tonight is going to be taken up
by family and packing, and I'll be at a wedding for the next few days
with limited net access (and no hardware access).

Cheers,
Matt

On Thu, Oct 25, 2012 at 5:10 PM, Vjekoslav Matic <vmatic at aon.at> wrote:
> Dear all,
>
> I am struggling since several days to get my *Seeeduino Mega 1280* board
> V1.23 running with Transterpreter-win-dev-20110201.1855.
>
> 1. I checked the hardware with Arduino IDE 1.0.1 and LED blink sketch on
> Arduino-pin 13 or 12 was running OK. This means there is definitely green
> LED on PCB connected to pin 13 and all HW is OK.
>
> 2. With Transterpreter I was apparently able to load the firmware and later
> also compile and download both heartbeat() and blink() examples. However,
> heartbeat() code was producing only short light pulses ~100 ms with ~500ms
> breaks and blink() example did not work at all = LED off(neither on pin 13
> nor on pin 12).
>
> 3. I checked all list discussions. Except concerns about LED.pin=-1 I did
> not find anything else.
>
> 4. I also tried to download the ARduino Mega tvm and compile & download code
> for Arduino Mega with same results as in point (2).
>
>
> Can you pls check if download transcript below is OK?
> Are there any known issues with these examples?
> Is there any other way to check if occam-pi code was really started on the
> tvm or if tvm is running at all? Can I access and communicate with console
> using UART?
>
> Thanks & Regards,
> Vjeko
>
>
> ---- my
> code -----------------------------------------------------------------------
> -------
> #INCLUDE "plumbing.module"
>
>
> PROC main()
>   blink(13,500)
>   --heartbeat()
> :
> ----------------------------------------------------------------------------
> ---------------
>
>
>
> ----- flashing firmware
> transcript ----------------------------------------------------
>
> Uploading Plumbing firmware
>
> avrdude.exe: AVR device initialized and ready to accept instructions
>
> Reading | ################################################## | 100% 0.02s
>
> avrdude.exe: Device signature = 0x1e9703
> avrdude.exe: NOTE: FLASH memory has been specified, an erase cycle will be
> performed
>              To disable this feature, specify the -D option.
> avrdude.exe: erasing chip
> avrdude.exe: reading input file "F:\Program
> Files\Transterpreter\arduino\tvm\firmware\tvm-avr-atmega1280-16000000-seeedu
> inomega.hex"
> avrdude.exe: writing flash (21842 bytes):
>
> Writing | ################################################## | 100% 6.86s
>
> avrdude.exe: 21842 bytes of flash written
> avrdude.exe: verifying flash memory against F:\Program
> Files\Transterpreter\arduino\tvm\firmware\tvm-avr-atmega1280-16000000-seeedu
> inomega.hex:
> avrdude.exe: load data flash data from input file F:\Program
> Files\Transterpreter\arduino\tvm\firmware\tvm-avr-atmega1280-16000000-seeedu
> inomega.hex:
> avrdude.exe: input file F:\Program
> Files\Transterpreter\arduino\tvm\firmware\tvm-avr-atmega1280-16000000-seeedu
> inomega.hex contains 21842 bytes
> avrdude.exe: reading on-chip flash data:
>
> Reading | ################################################## | 100% 6.42s
>
> avrdude.exe: verifying ...
> avrdude.exe: 21842 bytes of flash verified
>
> avrdude.exe done.  Thank you.
>
> firmware upload completed sucessfully
>
> ------- compile
> transcript -------------------------------------------------------------
>
> Compiling: F:\Documents and
> Settings\Vjeko\Desktop\HamRadio\Transterpreter\code\test\blink.occ
> compile completed sucessfully
>
> ------- run
> transcript -------------------------------------------------------------
> avrdude.exe: AVR device initialized and ready to accept instructions
>
> Reading | ################################################## | 100% 0.02s
>
> avrdude.exe: Device signature = 0x1e9703
> avrdude.exe: reading input file "blink.ihex"
> avrdude.exe: writing flash (24970 bytes):
>
> Writing | ################################################## | 100% 1.02s
>
> avrdude.exe: 24970 bytes of flash written
>
> avrdude.exe done.  Thank you.
>
> Any output from the connected device will appear below
> (hit stop to disconnect)
> ------------------------------------------------------
>
>
>
> _______________________________________________
> users mailing list
> users at concurrency.cc
> http://lists.concurrency.cc/mailman/listinfo/users